Anonymous

Carb mounts

Here’s where to discuss anything specific about your standard(ish) car or something that applies to the model in general.
Post Reply
timcar
Wedgling
Posts: 18
Joined: 19 Aug 2015 16:58

Carb mounts

Postby timcar » 27 Apr 2022 15:14

A quick search of Rimmers and Robsport seems to indicate that these "repro" versions of the originals are no longer available. I know that they were not as good as the originals and have seen somewhere (Beans?) solid aluminium versions. Are these being manufactured and for sale anywhere?

FI Spyder
TRemendous
Posts: 8915
Joined: 03 Jul 2006 19:54
Location: Canada

Re: Carb mounts

Postby FI Spyder » 27 Apr 2022 15:41

In our club trip to Disneyland, the first morning the other TR7 wouldn't start as the carb mounts had split. We zip tied them up for rest of the trip. I believe they were going to stop at Moss Motors on the way back (for a tour) and to pick up some aluminum blocks. I wasn't with them as I separated to visit relatives in Solvang, I can't remember if they got them there or not. They used to be available on eBay. This was back in 2011. I remember reading Moss carries less/little TR7 parts now.
- - -TR7 Spider - - - 1978 Spitfire- - - - 1976 Spitfire - - 1988 Tercel 4X4 - Kali on Integra - 2013 Volt - Yellow TCT

Beans
TRemendous
Posts: 7788
Joined: 15 Mar 2006 19:29
Location: Netherlands
Contact:

Re: Carb mounts

Postby Beans » 27 Apr 2022 19:52

I had my own made, but the Dolomite Club sells them to club members.
Try a search on FB . There are a few others who sell them.
Image
1976 TR7 FHC (currently being restored ...)
1980 TR7 DHC (my first car, a.k.a. Kermette)
1981 TR7 FHC (Sprint engined a.k.a. 't Kreng)

http://www.tr7beans.blogspot.com/

Rich K
Wedge Pilot
Posts: 291
Joined: 08 Aug 2015 18:04
Location: Worcester, United Kingdom

Re: Carb mounts

Postby Rich K » 28 Apr 2022 22:45

Back in the day I managed to cure poor running due to leaks in the rubber carb mounts by smearing silicone sealant around the outside surface of the mounts. It didn’t look too pretty but seemed to prevent air leaks through the splits in the rubber. Still had the same mounts in place years later at the point when I removed the 2 litre engine ready for a V8 upgrade.
1980 TR7 drophead now repainted and started refitting plus V8 upgrade
1977 TR7 fixedhead awaiting restoration
1981 TR7 drophead bodywork and mechanicals now done, completing trim currently.
Ford Ranger Wildtrak
Jaguar XKR Supercharged

stevie_a
TRemendous
Posts: 3325
Joined: 19 Jun 2005 10:28
Location: Glasgow'ish

Re: Carb mounts

Postby stevie_a » 29 Apr 2022 19:53

Rich K wrote:Back in the day I managed to cure poor running due to leaks in the rubber carb mounts by smearing silicone sealant around the outside surface of the mounts.


I have done that for now, aluminum mounts are still to be purchased at some point. ( I promise to get round to it at some point) :roll:
If it's not broke don't fix it.

Hasbeen
TRemendous
Posts: 6474
Joined: 28 Apr 2005 12:32
Location: Australia
Contact:

Re: Carb mounts

Postby Hasbeen » 30 Apr 2022 04:33

I supported my manifold with a couple of large stainless steel hose clips, used for connecting 4" lay flat hose to aluminium irrigation pipes about 15 years ago. Still going strong, with no sign of cracking. In compression it should last a while longer I expect.

No forced usage of E10 here in Queensland to increase deterioration of rubber either.

Hasbeen

dursleyman
TRiffic
Posts: 1571
Joined: 11 Jun 2007 22:55
Location: United Kingdom
Contact:

Re: Carb mounts

Postby dursleyman » 30 Apr 2022 11:24

I bought mine from the Dolomite Owners Club (you have to be a member) and they are excellent. Fit and forget.
The picture is on my Sprint engine but they are the same as TR7.

Image
Russ

1981 TR7 Sprint DHC & 1977 TR7 Sprint FHC
Dursley
UK

http://tr7russ.blogspot.co.uk/

Image Image

Post Reply

Who is online

Users browsing this forum: No registered users and 23 guests