Anonymous

TR7 - Water pump housing

Here’s where to discuss anything specific about your standard(ish) car or something that applies to the model in general.
Post Reply
Howard722
Rust Hunter
Posts: 176
Joined: 25 Feb 2008 07:22
Location: United Kingdom
Contact:

TR7 - Water pump housing

Postby Howard722 » 25 Jun 2021 10:00

How critical is the condition of the angled surface that faces the pump vanes. (12 vane)
My spare housing is quite badly pitted in one area,-re-usable or is it scrap?
Enjoy & regards

Hasbeen
TRemendous
Posts: 6474
Joined: 28 Apr 2005 12:32
Location: Australia
Contact:

Re: TR7 - Water pump housing

Postby Hasbeen » 26 Jun 2021 04:10

I have no real idea how much pitting would reduce water flow, but my guess would be very little. However it should be easy to fill the pits.

I once had a 6HP Petter marine diesel raw water cooled generator in a small island ferry. The actual sealing surface of the alloy cylinder head was corroded, probably due to a mixture of copper gasket, alloy head & salt water.

I removed any corrosion, & thoroughly cleaned the surface exposed, & filled the resultant recess with marine grade epoxy filler. I did this in the hope it would run long enough to get a replacement head from the UK to Australia.

6 years later the replacement head was still sitting on the shelf, & my patch up was still working.

Done properly I am sure a good quality epoxy filler/putty would hold up in the much cooler area of a water pump.

Hasbeen

dursleyman
TRiffic
Posts: 1571
Joined: 11 Jun 2007 22:55
Location: United Kingdom
Contact:

Re: TR7 - Water pump housing

Postby dursleyman » 19 Aug 2021 15:54

Howard722 wrote:How critical is the condition of the angled surface that faces the pump vanes. (12 vane)
My spare housing is quite badly pitted in one area,-re-usable or is it scrap?


Guessing you mean the water pump cover, there are lots about and they come up for sale pretty cheap all the time.
Be aware that the covers for the 6 vane and 12 vane pumps have a different angled surface and are not interchangeable.
Attachments
2019-07-23_17.41.35_pump_covers_1_16.jpg
2019-07-23_17.41.35_pump_covers_1_16.jpg (222.95 KiB) Viewed 4082 times
Russ

1981 TR7 Sprint DHC & 1977 TR7 Sprint FHC
Dursley
UK

http://tr7russ.blogspot.co.uk/

Image Image

tr7dan
Rust Hunter
Posts: 117
Joined: 18 Jun 2009 22:53
Location: United Kingdom
Contact:

Re: TR7 - Water pump housing

Postby tr7dan » 20 Aug 2021 21:31

I had my water pump reconditioned by Tony Hart and he said the pitting on my pump cover, which is quite bad, doesn't matter....

Beans
TRemendous
Posts: 7788
Joined: 15 Mar 2006 19:29
Location: Netherlands
Contact:

Re: TR7 - Water pump housing

Postby Beans » 20 Aug 2021 23:22

Pitting of the housing (or impeller) is usually not caused by corrosion but by cavitation (imploding air bubbles).
Once you have pitting it will only be amplified to a point where the pump doesn’t work properly anymore.
Image
1976 TR7 FHC (currently being restored ...)
1980 TR7 DHC (my first car, a.k.a. Kermette)
1981 TR7 FHC (Sprint engined a.k.a. 't Kreng)

http://www.tr7beans.blogspot.com/

Post Reply

Who is online

Users browsing this forum: No registered users and 37 guests

cron