Anonymous

Weathershields Sunroof fitting - HELP!

Do you have a question? Ask it here! The reference library for all your DIY instruction guides, aka ‘surely there must be an easier way of doing this’.
Post Reply
johnnyj
Rust Hunter
Posts: 220
Joined: 23 Jan 2016 12:12
Location: Northampton
Contact:

Weathershields Sunroof fitting - HELP!

Postby johnnyj » 16 Nov 2019 11:05

Hi folks. I am having a hell of a job refitting the above. I just can't get the roof to go back in, i.e. engaging all four sliders in the metal channels. I can get one side in but not the other; I've tried putting the whole roof in at an angle to kind of stretch the distance between the sliders and then straighten the whole thing up, but to no avail.

It came out over 20 years ago so "installation is the reverse of removal" as per the books doesn't work for me, as I have forgotten how it came out!!

Any advice is will be seized upon with much glee.

:D
John
Triumph TR7 FHC, 1977
http://t-r-7.blogspot.co.uk

Beans
TRemendous
Posts: 7795
Joined: 15 Mar 2006 19:29
Location: Netherlands
Contact:

Re: Weathershields Sunroof fitting - HELP!

Postby Beans » 16 Nov 2019 23:20

To long ago to remember correctly (blanking plates at the back of the sliding rails?)
Might have a look at a spare sunroof in the shed within the next few weeks if still needed :wink:
Image
1976 TR7 FHC (currently being restored ...)
1980 TR7 DHC (my first car, a.k.a. Kermette)
1981 TR7 FHC (Sprint engined a.k.a. 't Kreng)

http://www.tr7beans.blogspot.com/

johnnyj
Rust Hunter
Posts: 220
Joined: 23 Jan 2016 12:12
Location: Northampton
Contact:

Re: Weathershields Sunroof fitting - HELP!

Postby johnnyj » 18 Nov 2019 22:39

Thanks beans. I managed to get it in by putting it in at an angle, but doing that has destroyed one front slider (the plastic cap, not the metal bit). The sliders were aftermarket nylon parts from Littleport Boat Haven, and look like they are 3D printed.

Any ideas would be great.

Thanks

John
Triumph TR7 FHC, 1977
http://t-r-7.blogspot.co.uk

Beans
TRemendous
Posts: 7795
Joined: 15 Mar 2006 19:29
Location: Netherlands
Contact:

Re: Weathershields Sunroof fitting - HELP!

Postby Beans » 20 Nov 2019 21:50

On my Edrose there are ±10 cm gaps at the back of the side rails .
Feed in the sunroof's slides through these holes and move it as far forward as possible.
Fit the blanking plates (2 screws each) pull the sunroof back and fit the rear rail to the roof.
Image
1976 TR7 FHC (currently being restored ...)
1980 TR7 DHC (my first car, a.k.a. Kermette)
1981 TR7 FHC (Sprint engined a.k.a. 't Kreng)

http://www.tr7beans.blogspot.com/

johnnyj
Rust Hunter
Posts: 220
Joined: 23 Jan 2016 12:12
Location: Northampton
Contact:

Re: Weathershields Sunroof fitting - HELP!

Postby johnnyj » 12 Dec 2019 19:50

Hi Beans

I followed as far as "...Fit the blanking plates (2 screws each) pull the sunroof back and fit the rear rail to the roof."

What are the blanking plates?

Cheers

John
Triumph TR7 FHC, 1977
http://t-r-7.blogspot.co.uk

Beans
TRemendous
Posts: 7795
Joined: 15 Mar 2006 19:29
Location: Netherlands
Contact:

Re: Weathershields Sunroof fitting - HELP!

Postby Beans » 12 Dec 2019 20:36

I just read in your other post that you have a short sunroof, and that got me thinking ...
I misintepreted your type, I was referring to the (full length ) Edrose type ... apologies for the confusion :oops:
Image
1976 TR7 FHC (currently being restored ...)
1980 TR7 DHC (my first car, a.k.a. Kermette)
1981 TR7 FHC (Sprint engined a.k.a. 't Kreng)

http://www.tr7beans.blogspot.com/

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest

cron